loading

Inflatable workshop,focus on customer’s demands since 2000.

diy climbing hand holds

by:KK INFLATABLE      2020-06-07
Eastern Mountain Sports has plans on how to build their own indoor climbing wall like Eastern Mountain Sports on the Internet.
But there are only a few ways to have a full record for you to hold it yourself, and it can be expensive to buy them!
Also, make your own one-of-a-kind point of view more interesting, as no one will bring new challenges to your own wall.
I want to thank my friend Dave for showing me this and taking pictures for the first time.
There are various ways to make handrails from wood to bondo to silicone with fiberglass resin, and while they are all working, without a lot of practice time and a lot of money, there is no material spent on practice time.
Bondo fiberglass resin sand produces the best results and is very close to the commercial climbing stand you will buy in texture and feel.
The silicone holder is very expensive to make, it takes about $5 to make the mold, then it takes a few hours to make it, and then it is covered with silicone.
What\'s worse, it takes a few days to dry, and at this point you\'re ready to buy hold with a sledgehammer.
Don\'t let my frustration fool you with others, there is light at the end of the tunnel.
What I\'m going to show you is probably the easiest way to replicate commercial holding or make your own free form holding without a \"prototype.
Here\'s what you need :-
1 piece of clay ($5-
$15 is very good if you have a student ID card of 10% :)-
Bangduo fiberglass resin (
I found it easier to buy 1 gallon size at Home Depot, about $20)-
Additional fiberglass resin fixer (
About $2 to $4, one to two more per gallon resin)-
Play with sand or fine silicon sand (
Silicone works better, don\'t have pebbles or stones in it, starting at $5 to $10)-3/8\" Washers (about .
50 cents ea you need 1 or 2 hold)-
3/8 \"Mason drill for drilling-
A can of WD40Step 1 gets a piece of clay (
6 \"x 6\" by 12 \"depends on the type of clay, about 20 lbs)
It can be cheap clay;
Don\'t spend an arm and a leg on expensive sculpture clay, it\'s just not needed.
We will start with a clone commercial hold first, which is easier to start with when you first try.
Find a commercial container and cut a piece of clay deep enough to fit the depth of the container.
It is very important to push the hold directly down into the clay, keep the back up, and transfer the texture to the clay mold.
At this point, carefully remove the bracket from the clay.
Need to be careful not to stain the texture, so this may need to be tried several times first.
If the plug of the bolt hole breaks a new one from some extra clay by hand.
It is very important to place a 3/8 gasket on the top of the bolt hole Bolt.
Now you want to spray the finished mold with WD40, which will serve as a potion to prevent the pouring mixture from sticking to the mold.
The interesting part of the mixed bondo resin came.
This stuff smells, so do it in a well ventilated place, you may want to wear a respirator, and I don\'t recommend breathing with a respirator.
I like to set up a fan behind me, blow to my work area and blow the smoke away from me.
You will estimate how much sand the entire mold will fill and roughly measure the volume of sand in ounces to determine the number of blends you will need to fill the mold.
So now you want 60% of the sand and 40% of the bondo mixture based on this measurement.
The first thing you want to do is mix the resin and fixer one drop at a time before adding sand.
It is important to carefully measure the volume of the resin so that you can calculate the correct amount of the fixer to be added.
The more fixes you add, the faster it will be to keep the settings.
I usually use the suggested amount but try not to use less.
Now you need to work fast and the clock ticks because you only have about 15 minutes before the resin starts to solidify and Harden!
If you want to add some color to your stand, now is the time, acrylic paint works best, and you also want to add it before the sand.
Make sure you are creative :)
You \'ve done all this and you\'re ready to keep pouring the sand into what you want to do slowly.
When you pour it, you want to stir it to avoid creating lumps or dry sand.
The sand needs to be all wet by the mixture.
The 60/40 mixture is a good guideline, but keep adding sand until it looks like more sand will dry the mixture.
Now we can pour the mixture into the mold.
If you mix too much, it\'s better to have some small containers so you don\'t waste anything.
Pour the top of the mold and fill it to the edge.
Now we can pour the mixture into the mold.
If you mix too much, it\'s better to have some small containers so you don\'t waste anything.
Pour the top of the mold and fill it to the edge.
Let the stand cool and set for 1 to 3 hours depending on how many fixtures you have added.
It is ready when the top is hard, but still a little warm to keep.
It will damage the texture if you pull too early.
The resin/sand mixture is still a bit soft at this point, so you can cut off any small irregularities with a knife, and I like to use a practical knife.
This you can smooth the back of the bracket by scraping on any rough surface like the sidewalk :)
At this point, you want to get your stand to the drill bit, or you can use the 3/8 Mason drill bit we bought before to eyeball and use the hand drill.
You want to drill by the washing machine.
Although the bolt Bolt brings us a starting hole, it will never be there all the time.
So now you just have to harden it for a few hours (let it cure)
And nail them on the wall.
Happy climb :)
Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...